Brooks Plumbing Co. Blog: Archive for July, 2012

Garbage Disposal Repair: Why is My Garbage Disposal Making Noise

Monday, July 30th, 2012

When you are looking for garbage disposal repairs in Olympia, call Brooks Plumbing Company. One of the more common service calls we get for kitchen plumbing repairs is a broken garbage disposal, particularly for “humming” garbage disposals. A humming garbage disposal can mean there are a few possible scenarios happening, but first, you’ll need to know what signs to look for.

A humming garbage disposal usually means that when you flip the switch to turn the disposal on, it doesn’t grind the food. Instead, it just makes a humming noise instead of the normal noises of a fully-functioning garbage disposal. This typically means that the blades are not working to chop the food waste. Here are a few reasons why this may have occurred and why you could need a repair service.

The first potential reason for a humming garbage disposal is a stuck flywheel. The flywheel is located just above the lower hopper chamber, and it is the device that turns the blades. The humming noise could mean that the blades are not turning because the flywheel is stuck. This is an easy repair that our technicians can take care of fairly quickly.

If the garbage disposal does not work after we fix the flywheel and reset it for you, the humming could be caused by a seized motor or a frozen bearing. In most cases, a seized motor or bearing means that the unit will need to be replaced. Before you try to repair or replace a garbage disposal yourself, it is best to call Brooks Plumbing Company to schedule an appointment.

Whether or not you need a replacement, Brooks Plumbing is the plumbing contractor to call for garbage disposal repair and replacement services in Olympia. If you decide that you want us to install a new garbage disposal, we can remove the old unit and replace your disposal with any number of new models to suit your needs and your budget. We carry a large selection of the latest models, and our technicians make it a priority to provide expert service for any plumbing job. Call today!

Continue Reading

Tags: , , , ,
Posted in Plumbing | Comments Off on Garbage Disposal Repair: Why is My Garbage Disposal Making Noise

Plumbing Guide: Sump Pumps Provide Relief for Wet Basements

Monday, July 23rd, 2012

Many homes in the Lacey area require sump pumps to keep their basements dry. Sump pumps are placed in pits or “sumps” in the basement floor. When the basement floods, it starts at the lowest point, which is the sump. As the sump fills with water, the pump is automatically activated and begins to suck the water out of the sump and discharge it to a drain or a line leading away from the house before it can flood the basement.

 How Sump Pumps Work

The pump’s base has openings to allow water to flow into it. When water fills the sump it also fills the interior of the pump. When the water reaches a certain level it triggers a floating switch that activates an electric motor. The motor spins a metal shaft immersed in the water at the bottom of the pump. The shaft is attached to an impeller, which resembles a small, sideways water wheel.

As the impeller spins at high speed it whirls the water away from the center of the pump, forcing it into a discharge pipe that rises up out of the sump. The discharge pipe connects to a length of hose or pipe that empties the water into a sink or outside the foundation of the house. As the water is forced out of the pump it creates a vacuum that pulls more water into the pump and out of the sump. The impeller keeps spinning and pumping water into the collecting pipe until the water level inside the pump – and the sump – allows the float switch to drop low enough to shut the motor off.

 Types of Sump Pumps

There are pedestal sump pumps and submersible sump pumps. In pedestal pumps, the motor assembly is above the base of the pump and the impeller, and doesn’t contact the water. The activation switch for the motor is attached to a long shaft with the float on the other end that drops into the water. As the water rises, it pushes the shaft up and activates the switch. Submersible pumps are smaller units with the motor, activation switch, and impeller all on one level. The motor compartment is waterproof. Either style pump is usually connected to the house electric circuit. But some homeowners connect them to backup battery power supplies so the pump will work in the event of a severe storm and power outage.

 Which Lacey Homes Need Sump Pumps

Every homeowner in Lacey should understand the concept of the water table. Simply put, the water table is the permanently saturated layer of soil, sand, or rock below most of the surface of the Earth. In some places it’s hundreds of feet below the ground, but in most areas it’s much closer to the surface. In temperate or seasonal areas, the depth of the water table can rise and fall.

The foundations of homes in the Lacey area are built above the water table. But seasonal fluctuations and heavy precipitation can cause the water table to expand upwards. If a basement isn’t completely waterproof, and few basements are, the water will seep in. Land near rivers, streams, and wetlands tends to have a very high water table, so homes built in those areas are particularly susceptible to flooding.

Although most basements are not waterproof, they should be able to withstand an occasional increase in the saturation of the soil around and beneath the house. A permanently damp basement could indicate that the foundation is close enough to the water table to prevent the basement from ever completely drying out.

If you are interested in learning more about sump pumps, give Brooks Plumbing Co. a call!

Continue Reading

Tags: , ,
Posted in Services | Comments Off on Plumbing Guide: Sump Pumps Provide Relief for Wet Basements

Plumbing Question: What Causes Low Water Pressure?

Monday, July 16th, 2012

Low water pressure in your Olympia home can make just about everything from showering to cleaning more difficult. It is frustrating, but it often seems like there is very little you can do about it. In fact, you may be able to improve your water pressure in a variety of ways, but the appropriate technique will depend on the root cause of your problem.

There are several different possible causes for low water pressure. If the problem is limited to certain areas or fixtures in the house, it may very well be because the pipes feeding that area or fixture are too small. Smaller pipes will only allow a smaller amount of water to pass through at once, making it impossible for you to get the force you are after.

Fixing this, of course, means putting in larger pipes, and that may be easier said than done. However, if the problem is on a small scale, you should not have too much trouble or need to pay too much to have a Olympia plumbing professional complete the job. A problem in a particular fixture can also result from small clogs or backups in the fixture itself, and this is a relatively easy situation to remedy as well.

A low water pressure problem that affects your whole house can result if the main pipes feeding into your house are too small. This could be the case if your house has been added onto since it was built or if you have more people living there now and using more water.

Replacing those incoming pipes is a big job, but it is often the only way to increase your water pressure and make it possible for the system to satisfy the water needs of the house. This is definitely something you will want to have a professional work on, and while it can be costly, it will be well worth it in the end. For more tips on how to improve your Olympia plumbing, give Brooks Plumbing a call!

Continue Reading

Tags: , , , ,
Posted in Services | Comments Off on Plumbing Question: What Causes Low Water Pressure?

How to Lower Energy Costs for Your Home: Water Heater Tips

Monday, July 2nd, 2012

If you want to lower the energy costs for your Lacey home, the water heater might not be the first place you’d think to save energy. However, when you add up the savings from a few easy steps that can improve your water heater’s efficiency, it can make a significant difference in your utility bills.

Here are some of the ways you can reduce the use of hot water in the home and increase your energy savings.

Saving Energy by Using Less Hot Water

Even if you own an energy-efficient, tankless water heater, and you try to conserve water as much as possible, hot water usage can always be reduced in other areas. Installing low flow faucets and fixtures can provide up to 60% in water savings because they reduce the flow rate (gallons per minute) for each fixture. Tankless water heaters are also more efficient when they are used with any application with a lower flow rate.

Replacing older appliances that require a lot of hot water with more energy-efficient models is worth the money and effort because of the energy savings you will get in the end. Make sure you fix any leaks on older hot water faucet or fixtures. A leak that costs a dollar or two extra per month doesn’t seem like much, but it will add up over time.

Lower the Temperature on Your Hot Water Heater

For every 10°F that you lower the water temperature on your hot water heater, you save between 3% to 5% in energy costs. The manufactured setting for most water heaters is 140°F, but most homes only require a maximum temperature of 120°F. Check your owner’s manual before you lower the temperature on your water heater to find out what the recommended settings are and how to change them.

Insulate Your Water Heater Tank and Water Pipes

Whether you have a gas or electric hot water heater, you can find fairly inexpensive and easy-to-install insulators or “jackets” for your water heater tank. Every tank has an R-value that determines how much heat it loses, so unless it is a high value, your water heater tank needs insulation. Call a Lacey plumber or check your owner’s manual for the R-value of your hot water heater, but the general rule is that if the tank is warm when you touch it, you need more insulation.

You can reduce emissions and your energy costs simply by paying more attention to how much hot water you are using in your Lacey home. For more tips and expert advice, call Brooks Plumbing Co to speak with one of our technicians.

Continue Reading

Tags: , , ,
Posted in Services | Comments Off on How to Lower Energy Costs for Your Home: Water Heater Tips